Mechanically lock the vehicle using the Drivers door using a second key. Protect your purchase with an extended warranty at Car Keys Express. Turn the key to on position, and cycle the key three times off-on-off-on-off-on. This device features a unique durable shell case which protects the advanced interior electronics from the wear and tear of daily use. If you have a newer model check out my. Nov 23, 2012 You will need a 1632 Watch Electronics battery to begin.
The actual procedure takes a few seconds to complete and many dealerships will do it for free as a courtesy. Insert the key in ignition. The only tool needed to change the battery is a small flathead screwdriver used to pry apart the two halves of the key fob. From your purchase to any questions you have after receiving your items, Car Keys Express is here for you. Line up the back cover of the key fob with the front half and gently snap them together. The only tool needed to complete this battery change is a small flathead screwdriver. It will need to be referenced in order to fulfill the warranty.
Turn the key to on position,and cycle the key three times off-on-off-on-off-on. Then with the key fob remote select your remote and then try to operate the vehicle with remote. This is usually just a case of dead batteries and is easily resolved by replacements. Then, unlock your doors in the traditional manner. Remove key from ignition and check for operation. If you find yourself struggling to get into your Toyota when your Smart Key malfunctions, read about how to unlock and start your car manually below. Note: I am not a registered charity.
System should now lock and unlock vehicle once, twice or five times depending which mode has been selected. On that case dealer is the only option. The actual procedure takes a few seconds to complete and many dealerships will do it for free as a courtesy. Check for this code in your owners manual - it will usually be either a sticker or small card in the booklet. Please keep track of your order number! This device requires programming by your local dealer or locksmith.
Dec 04, 2012 Try with brand new key fob battery and see. Donations are not tax deductible. Wait 6 seconds and press the unlock button once to activate the coding procedure. Gently slide the old battery out of the socket with your fingernail or carefully use the small flathead screwdriver to pry it out. Re-insert the remote control unit in to the front cover of the key fob with the rubber buttons fully inserted in place. If your dealer does charge a fee, local locksmiths usually charge much less to remain competitive.
Inside, you will find a small green circuit board that houses the small battery. Also car shows fuel pressure? When I popped open the Toyota key fob, the buttons went flying across my desk. We strongly recommend calling a Local Auto Locksmith for help here. The battery size could have been easily determined by opening up the fob before rushing off to the store. The procedure takes only a few seconds to complete and many dealerships will do it for free as a courtesy. We recommend changing the battery in Toyotas every 4 years. On that case dealer is the only option.
If you found this guide to be helpful, please consider making a small donation by clicking on the PayPal. Insert the small flathead screwdriver into the recessed slot and turn the screwdriver to separate the top and bottom halves. In some Highlanders, you may need to re-enter a security code to get your radio to work again. Programming instructions not included with the purchase. Pull off the top or bottom half of the key fob and remove the remote control unit. If you use the screwdriver to pry out the old battery, try to avoid damaging the green electrical circuit board.
They're known to go bad and it's a pretty likely cause for your problem, provided your fuses are not blown. If the remote s faulty then keyfob will not get programmed. Items sent back packaged improperly or that are lost or damaged will be the responsibility of the customer. Then with the keyfob remote select your remote and then try to operate the vehicle with remote. Insert the key in ignition. I suggest you to go through the list and click the link below to go through its details and procedure:------- 2009 Toyota Highlander: Smart Key Not getting Detected? For more, check out my other. If you can't find it, call Toyota and they will give you the code for free.
Otherwise May be keyfob needs to be reprogrammed. You must get an Automotive Locksmith to program the remote to your vehicle for you. Occasionally, Toyota Smart Keys will stop working. Please help support this website by shopping at. To start your car, depress the brake and push the start button like normal while holding the key fob as close as you can to the start button. Any return may be subject to a 18% restocking fee. Wait 6 seconds and press the unlock button once to activate memory erase.