Any wheel from a 97+ grand prix will fit any other grand prix. SureStop, a team with over 200 years of combined automotive experience, is a world-renowned leader in brake technology and product development. At Andy's Auto Sport, we have a huge variety of Pontiac Grand Prix wheel spacers to ensure that you have every wheel spacer option available to you. All Factory Wheels is here to help. Otherwise, nobody's been checking it because they are either lazy or uneducated.
Always refer to Owner's Manual for proper factory specifications that take precedence over the listed recommendations. Check your vehicle owner manual for specifications. Most of today's Pontiac Grand Prix wheel spacers, however, are finely crafted pieces of machined aluminum or steel that safely push your wheels out for a wider stance and wheelbase, which improves handling and the overall look of your vehicle. All of our aluminum wheels are top-quality and backed by our exclusive industry leading warranty. Just remove the plastic engine cover and trace the top water hose from the radiator back to the thermostat housing.
To find out you need to compare your bolt pattern with the bolt pattern of the wheel you have on hand. That way i was finding my car's bold pattern. Look deep into the trunk, near the back seat and you should see a large, round C clip, maybe 4 inches in diameter. Replacement Wheel Hub replaces your worn or warped factory unit. Wheel Dimensions There are four important measurements that are used to categorize and identify a wheel for fitment purposes.
All Replacement items are backed by a 1-year, unlimited-mileage warranty. Push the end of the switch in to turn on the cruise control, push again to turn it off. This expands the number of fitments the wheel applies to. Also measure in mm, for example 5x114. When your brakes squeal or grind or you feel your vehicle shaking or pulsing when braking, you may need to replace your brake pads or shoes. Disc brake systems use brake rotors and pads along with a caliper that presses the pads into the rotor.
Basics are that you compress the springs first then start in the engine compartment for the front struts at the strut mount assembly or pull back your trunk liner to expose the rear strut mounts. In these holes you may be able to see but rest assured, they are there four steel rods, non threaded, that have a steel bar holding them in place. Pontiac - Vehicle Bolt Pattern Reference On these pages you can find Pontiac vehicles Bolt Pattern and Offset. Disconnect the in and out lines by softly squeezing… This is usually cause by low power steering fluid level. Then i recorded the make, model and year of the car and was looking for the wheel information about that rims. This is not exact, but it will usually get you in the right ballpark.
The same is true of brake drums. It has a plastic covering that reads sensor. When you get to the speed you want, push down on the switch to set. Except for some spares and smaller wheels which may not have enough clearance to fit on 04+ due to the larger brakes. Since 2000, Centric Parts has supplied the automotive aftermarket with high-quality replacement brake parts. It is often recommended that you replace brake rotors and pads at the same time, but rotors can also be resurfaced in some cases and kept in service longer.
Sometimes its difficult to find out about the specific information about the rims if you only have the wheels but no stud or bold pattern information. This will help you in determining High or Low offset and bolt patterns of your vehicle. How do I know which size of spacer to get? If possible it is always best to test fit wheels and tires to your car, take measurements and then order the appropriate spacers. Most rims are interchangeable from one car to another car. A: Wheel spacers are carefully machined metal inserts that fit over your hubs between the wheel and hub face to move the wheel further away from the hub face. Since most wheels are mass produced, they have a large center bore to accommodate several different vehicles. You're also going to need either a torq socket or an allen wrench I've seen both to release the center retaining stud and hold the strut shaft while you remove the outer nut.
This distance will give you a rough idea of how much further you can safely go. Check your vehicle's manual for correct settings. Play with specs, try different settings and combinations, compare results. Use of this site implies your agreement to these terms. Torque: All alloy wheels should be installed using a torque wrench.
If you are buying spacers for a new set of wheels the best way to get it right is to determine the width and offset of your existing wheels and compare it to that of your new wheels. . Hubcentric wheels take the stress off the lug nuts, reducing the job of the lug nuts to center the wheel to the car. The 2008 Pontiac Grand Prix Base Model bolt pattern is 5-115 mm. Go into the trunk and pull out the carpet.