Remove the bolt that retains the sensor. Press down on the valve lifter with special tool and place a stopper between the camshaft and valve lifter. Battery voltage above 10 volts. Start the engine and check for leaks. Warm the engine until the engine reaches operating temperature.
Immediately after using the oil, replace the cap on the container and seal it to avoid moisture absorption. Remove the self-tapping screws A , the mounting nut B , the mounting bolt C and the blower unit D. Check the sensor for contamination, deterioration or damage. When the slot in the wheel aligns with the sensor, the sensor voltage output is low. Failure to do this may result in personal injury or death. Remove the cylinder head mounting bolts in sequence as shown. The recommended replacement interval for timing belts is 60,000 miles.
Installation is the reverse of the removal procedure. Disconnect the negative battery cable. Remove or disconnect the following: Negative battery cable Accessory drive belts Timing belt Oil pan Oil screen Front case Cover from the front case Inner and outer rotors from the front case Fig. Personal injury or death may result if the system test is not performed properly. All Hyundai models use interference-type non-freewheeling engines. If dropped, the sensor may be inoperative, could result in occupant injury, or possibly death.
Install the drive belt to the alternator. Install the cylinder head cover. Before servicing the vehicle, refer to the Precautions Section. Install or connect the following: Crankshaft timing sprocket Timing belt Front covers Accessory drive belts Negative battery cable 3. Using a micrometer, measure the cam lobe height. Page 129 Back to Top Fig.
Install the air deflectors to the top of the radiator. Possible Causes: Page 89 Clear the trouble codes and retest for this trouble code. Rear struts: Tighten to 22-30 ft. Before servicing the vehicle, refer to the Precautions Section. Remove the heater and evaporator unit.
Lower the jack and remove from under the vehicle. Install or connect the following: Front crankshaft seal Oil screen Oil pan Timing belt Accessory drive belts Negative battery cable 6. If problem corrected replace the component. Remove the engine cover and intake manifold. Remove the main crash pad.
Before servicing the vehicle, refer to the Precautions Section. Before servicing the vehicle, refer to the Precautions Section. Before servicing the vehicle, refer to the Precautions Section. Drive belt adjustment diagram Inspect the drive belt for signs of glazing or cracking. Install the right front tire and wheel. Next, unscrew the exhaust manifold if anyone will desire a little extra to disassemble The valve itself. Rotate the crankshaft clockwise the angle equivalent of two teeth of the camshaft sprocket.
I was inquiring to see if anyone has any tips for simplifying the removal of the intake manifold on this particular engine. Measure the resistance between terminal 2 and 3 component side ; specification should be 14. Disconnect the tie rod end ball joint from the knuckle using the special tool 09568-34000. Remove or disconnect the following: Front wheel Lower ball joint Lower control arm mounting bolts Lower control arm To install: 1. Install the idler pulley and tighten the bolt to 32-40 ft. Negative battery cable Accessory drive belts Cylinder head cover Timing belt Page 8 Camshaft sprocket Timing chain auto tensioner Camshaft bearing caps and camshaft timing chain Intake and exhaust camshafts Mechanical lash adjusters Fig.
Condition 3 stuck signal engine coolant temperature less than 104 degrees F. Warm the engine until the engine reaches operating temperature. Remove the ammeter and voltmeter and the engine tachometer. Install the upper oil pan. If it is lower but the alternator output wire is in good condition, remove the alternator from the vehicle and test it. Remove 4 bolts and water pump pulley.
Always keep fuel in a container specifically designed for fuel storage; also, always properly seal fuel containers to avoid the possibility of fire or explosion. Remove the 4 bolts and timing belt upper cover. . Camshaft timing chain alignment marks-2. Lay a strip of plastigage across each of the camshaft journal. Disconnect the ball joint from knuckle using the special tool 09568-34000.