Pull the round knobs on each side of the extender to unlock it. See your dealer or a reliable trailer dealer if you require assistance. See your dealer or trailer rental agency for proper instructions and equipment for hooking up trailer lamps. Replace any lost coolant and check for leaks prior to reinstalling the fiber cover. Children must always be properly restrained.
Thought by adding a high pressure gear lubricant this would silence the noise. Washing your vehicle Wash your vehicle regularly with cold or lukewarm water. Always check the condition of the drain plug and gasket before reinstalling. Using the proper fluids will ensure your engine is operating at optimal performance. Always set the parking brake fully and make sure that the gearshift is securely latched in P Park automatic transmission or in 1 First manual transmission.
All capacities include adding a new filter. If a replacement oil filter is used that does not meet Ford Material and design specifications, start-up engine noises or knock may be experienced. The R-2 is known for leaking oil from a rubber plug in the top cover. Washer fluid placed in the cooling system may harm engine and cooling system components. Refer to the scheduled maintenance guide for maintenance intervals. Make sure your trailer lamps conform to local and Federal regulations. To stop on a particular selection, press the control again.
Engine oil drain plugs on all the vehicles torque at between 15 and 25 foot-pounds. For vehicles with overflow coolant systems with a non-pressurized cap on the coolant recovery system, add coolant to the coolant recovery reservoir when the engine is cool. Always disconnect the battery before servicing high current fuses. If brake fluid contacts the eyes, flush eyes with running water for 15 minutes. Unfortunately there is no easy fix here as the transmission must be removed to replace the combination slave cylinder and throwout bearing. Do not use household or glass cleaners. Use extra caution while becoming familiar with your vehicle.
If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap. What difference does it make? These quality accessories have been specifically engineered to fulfill your automotive needs;. If your vehicle is equipped with a 3. The decisions of the Board are binding on Ford and, in some cases, on the dealer but not on consumers who are free to pursue other remedies available to them under state or federal law. Make sure the jack is fastened so it does not rattle when you drive.
The shift cover was modified in 1995 to have a taller shift cover and neutral position switch in cover was eliminated. If equipped, unlock and remove the spare tire carrier lock from the rear access hole located just above the rear bumper and below the tailgate. Flash to pass Pull toward you to activate and release to deactivate. Clean with a tar remover if necessary. For the life of me I cannot figure out why the level is high if it is supposed to hold over 10 quarts. Driving with a 5—speed automatic transmission if equipped Your automatic transmission electronically controls the shift feel by using an adaptive learning strategy.
Failure to adjust the safety belt properly could reduce the effectiveness of the seat belt and increase the risk of injury in a collision. Always set the parking brake fully and make sure the gearshift is latched in P Park. Lay the tire on the ground with the valve stem facing up. There are three sets of menus available depending upon which mode or feature is activated. Belt minder The Belt Minder feature is a supplemental warning to the safety belt warning function. The playing media will mute momentarily. Parts and accessories for the engines are largely interchangeable, but fluid levels and types do fluctuate.
Make sure the headlamps and vehicle accessories are off. Press the control to activate and deactivate the Dolby noise reduction. Probably doesn't matter about hose placement, but I always mark them just in case. Refer to Stowing the spare tire. This position locks the transmission and prevents the rear wheels from turning. Temperature control knob Controls the temperature of the airflow inside the vehicle. Depends It depends on what transmission it has.
To avoid scratching the lamps, do not use a dry paper towel, chemical solvents or abrasive cleaners. Stow the jack and lug wrench. Each seating position in your vehicle has a specific safety belt assembly which is made up of one buckle and one tongue that are designed to be used as a pair. You will need 3 plugs. Stop the vehicle as soon as safely possible, switch off the engine immediately and let the engine cool. And my rear diff is not a Limited slip, could I use the gear oil there? If it enters the red section, the engine is overheating.
When the light is on, the transmission does not operate in the overdrive mode, refer to the Driving chapter for transmission function and operation. Install the bulb socket in lamp assembly by turning clockwise. Insert the indicator fully, then remove it again. In 1998 the stub stick in shift cover was changed to accept shift lever with groove on right side. Transmission operates in gears one through four. Locate the correct anchor for the selected seating position.