Rocker Arms Engine Oil 45 ft-lbs. A bolt goes through the center of the knock sensor, which then mates the sensor to the block on each bank. Rocker Studs screw-in Engine Oil50 ft-lbs. Oil Pump Engine Oil 15 ft-lbs. Could you also include intake manifold, plenum, and throttle body torque specs as well? Uniformly tighten the bolts in several passes. Bolt - Rod Cap Type: Dim: Length: Head: Grade: Connecting Rod To Crankshaft 75 Ft-Lbs 900 In-Lbs 101.
It is very important to the life of these engines that oil changes are done on a regular basis. Bore and stroke is 92 mm × 83 mm 3. Ford V8's with medium- or low-rise cylinder heads. Intake manifolds are responsible for distributing evenly a combustion mixture or air to each intake port in the engine's cylinder heads. If it is regularly maintained and smoothly run, the motor is quite safe and serves long. Type: Dim: Length: Head: Grade: Oil Pan To Engine Block 7.
Ford V8 352, 360, 390, 406, 427, 428 Firing Order Cylinder Numbering Distributor Rotation Rotor Under Cap Spins: Counter Clockwise Torque Specs These specs may not be correct for your application. Main Cap Crossbolts 406 and 427 Engine Oil 40 ft-lbs. Centerbolt HarmonicDamper Engine Oil60 ft-lbs. At the back of the heads each cam has a gear and both intake and exhaust cams are geared to each other each cam has one dot but both have 2 dots 180 degrees opposite single dot. But just go to a mechanic and he can tell you. This engine's cylinders fire in a 1-2-3-4-5-6 order.
Manufacturers set specifications for their components, such as torque specifications, which are expressed in foot-pounds. Install the bolts and tighten them finger-tight and torque in 4 steps according to the pattern mentioned: step 1: 36 in-lbs; step 2: 72 in-lbs; step 3: 120 in-lbs; step 4: 144 in-lbs. Edelbrock Part 2105 Performer 390 intake manifold is designed for street 332-352-360-390-406-410-427-428 c. Foot Pounds on the Lower and Inch Pounds … on the Upper. Bellhousing Transmission to Block Engine Oil 25 ft-lbs.
Uniformly tighten the bolts and nuts in the sequence shown in the illustration. Bore and stroke is 87. Also it is best to tighten the fasteners in 2 or 3 steps to ensure an even installation. Always use a tap or thread chaser on all bolt passages and bolt threads before attempting re installation. It also has to do with the compression ratio of motor too. This set up works for both the drivers side and the passengers side, don't sweat which side you are on. Type: Dim: Length: Head: Grade: Oil Pan To Engine Block 13.
The problem associated with high oil consumption is a usual thing for them. Disconnect heater inlet water hose 13. Edelbrock's Patented Dual-plane, low-rise design with a 180-degree firing order greatly improves torque over a wide rpm range for excellent throttle response from off-idle through 5500rpm. Bolt Type: Dim: Length: Head: Grade: Oil Filter Adapter To Engine Block 13. The intake manifold also operates as a mount for the throttle body, carburetor, fuel injection, and other engine components. To ensure engine stability, engine bolts must be torqued or bolted down to a certain weight specification under manufacturer guidelines. Number the bolts as follows: top row left to right 13 5 2 10.
Bolt - Rod Cap Type: Dim: Length: Head: Grade: Connecting Rod To Crankshaft 45 Ft-Lbs 540 In-Lbs 61. It may need a replacement. Install the fuel pipe clamp. Inspect cylinder head set bolt 40. Cam Sprocket upper gear Thread Locker20 ft-lbs.
Bolt - Rod Cap Type: Dim: Length: Head: Grade: Crankshaft To Engine Block 75 Ft-Lbs 900 In-Lbs 101. I have replaced knock sensors and valve cover gaskets on my car and now put back together. . Then remove the water outlet together with the water bypass hose No. Centerbolt Harmonic Damper Thread Locker 90 ft-lbs. Here is a guide that will help you with the job along with some diagrams below Apply seal packing to the cylinder heads as shown in the illustration. Clutch Pressure PlateThread Locker35 ft-lbs.
The engine is a 60 degree V6 design. There is of course a sequence involved in all three … cases, but that is a bit difficult to describe here. They can become contaminated easily. Clutch Pressure Plate Thread Locker 35 ft-lbs. This is necessary to maximize the engine's efficiency and performance. Using a socket hexagon wrench 8, remove the hexagon bolt.