To make sure that the Dodge Ram 1500 headlight assembly is in its optimum condition, follow these cheap, quick, and trouble-free maintenance and cleaning tips. Cracked or chipped headlight housings Since the headlights are located in front of the vehicle, it is more susceptible to damage. This article applies to the Dodge Ram. The headlight switch controls the headlights as well as the truck's interior lights. To learn how you can install them yourself on your Dodge Ram, read through the.
Step 2 — Remove bolts There are 10mm bolts holding the grille in place; remove them and take off the grille. Open the wheel well access panel and wedge it on the top of the tire to hold it in place. It may be easier to just leave the fasteners in the radiator cover rather than pulling them entirely out. Install the plastic welting along the inner edge of the headlight assembly. Two weeks later it arrived and I had a mechanic install the part. As I get to my car I look and notice the driver side mirror is dangling by a thread.
The only minor hiccup was the gaskets. Remove the two screws with the 10mm socket and ratcheting wrench by turning them counter clockwise. Turn the wheels all the way to the opposite side of the burnt out headlight bulb that you are replacing. Step 5 — Re-install headlight housing Once the new headlight is in, place it back into the housing unit, and pop back in the headlight retaining tab. You see, this simple tip can greatly extend your headlight assembly's life service.
Install the socket into the rear of the headlight assembly and turn it clockwise to lock it in place. Now remove the 10mm bolts holding the headlights in place. The video above shows you to replace the headlight in your 2015 Ram 2500. This article applies to the Dodge Ram 2002-2008. However, be careful not to scratch the surface when cleaning because this type has a similar structure as sandpaper.
In addition, it is also a good idea to cover the bumper with an old towel when doing maintenance to prevent contamination. Step 4 — Pull the headlight out and swap the bulb Pretty straightforward; just be careful while handling. Headlights grow dimmer by up to 20% over time and eventually burn out - for this reason, we recommend changing your headlights in pairs. Move to the wheel well access panel and pull the white plastic slide lock in to the down position. Test the new bulbs by turning on the headlights, flashing the high beams and activating the hazard signals. This article applies to the Dodge Ram 1994-present.
She now has plenty of light to get back college a few states away. You see, the electrical wirings connected to the headlight assembly can become loose overtime. Step 3 — Open up the panels of the front wheel wells Again, using the panel popping tool, open up the panels in the front wheel wells they have a tiny tab holding them in place and this tool makes it super easy to remove. Tighten the two headlight screws with the 10mm socket and ratcheting wrench. Do not remove the headlights just yet. Slide the headlight assembly back into the truck and install the three mounting bolts, tightening them with a socket and ratchet. If you do get the bulb dirty, wipe it clean with an alcohol moistened paper towel.
Remove the four bolts by turning them counter clockwise with the 10mm socket and ratcheting wrench. Set them aside in a safe place. Overall, for the money, these are hard to beat! You see, the alternator keeps the battery charged. Close the hood or move to the second headlight and repeat the process for the opposite bulb. Donations are not tax deductible.
Replacement of the bulb requires the removal of the headlight assembly, as access to the lights is from the rear of the assembly. You see, the oil from the skin can affect the light bulbs' life service. Push the slide lock straight up to release it. Changing both headlight bulbs on your Ram 1500 at the same time will allow both bulbs to have the same intensity and prevent the new headlight bulb from appearing brighter than the bulb on the opposite side. To gain access to the headlight bulbs, you'll first need to remove the black plastic radiator shield and also the front grille of the vehicle. To help avoid scratching the painted bumper or the plastic headlight lens, place a towel in between them.
If you have trouble moving the slide lock, push on the headlight with your other hand while sliding the lock down. Line up the friction fasteners at the bottom of the grille with the slots on the front of the vehicle. Pop in the smaller inner piece of the wheel well liner fastener. Push the headlight assembly back in to place and insert the two 10mm screws. A great way to spruce up the interior of your truck is to change out the dash lights to.